| Model | Engine | Capacity/Filter Capacity Litres(liters) | Oil Change Intervals |
|---|---|---|---|
| Qashqai 1.6 (2007 – 2010) | HR16DE | 4.3 | n/a |
| Qashqai 1.6 (2010 – 2014) | HR16DE | 4.3 | 30 000 km/ 12 months |
| Qashqai 2.0 (2007 – 2010) | MR20DE | 4.4 | n/a |
| Qashqai 2.0 (2010 – 2014) | MR20DE | 4.4 | 30 000 km/ 12 months |
| Qashqai 2.0 AWD (2007 – 2010) | MR20DE | 4.4 | n/a |
| Qashqai 2.0 AWD (2010 – 2014) | MR20DE | 4.4 | 30 000 km/ 12 months |
| Qashqai 1.5 dCi (2007 – 2010) | K9K | 4.4 | 20 000 km/ 12 months |
| Qashqai 1.5 dCi DPF (2007 – 2010) | K9K | 4.4 | 20 000 km/ 12 months |
| Qashqai 1.5 dCi (2010 – 2014) | K9K | 4.6 / 0.2 | 20 000 km/ 12 months |
| Qashqai 1.5 dCi DPF Euro 4 (2010 – 2014) | K9K | 4.6 / 0.2 | 20 000 km/ 12 months |
| Qashqai 1.5 dCi DPF Euro 5 (2010 – 2014) | K9K | 4.4 / 0.1 | 20 000 km/ 12 months |
| Qashqai 1.6 dCi DPF (2012 – 2014) | R9M | 5.5 / 0.4 | 30 000 km/ 12 months |
| Qashqai 1.6 dCi AWD DPF (2012 – 2014) | R9M | 5.5 / 0.4 | 30 000 km/ 12 months |
| Qashqai 2.0 dCi (2008 – 2010) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi DPF (2008 – 2010) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi (2010 – 2014) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi DPF (2010 – 2014) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi AWD (2008 – 2010) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi AWD DPF (2008 – 2010) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi AWD (2010 – 2014) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
| Qashqai 2.0 dCi AWD DPF (2010 – 2014) | M9R | 7.4 / 0.4 | 20 000 km/ 12 months |
How to change oil filter and engine oil on NISSAN QASHQAI j10
Here’s the tools you will need to successfully change the oil filter and engine oil on your Nissan Qashqai J10. I’ve provided you with Amazon links to each product, should you need any of them to complete your oil change.
Important Information
- Replace the oil filter every time when changing motor oil.
- All work should be done with the engine stopped.
- Wear gloves to prevent contact with hot liquid.
Step-by-Step Guide to Changing the Oil Filter in a Nissan Qashqai (J10 Series)
Step 1: Begin by opening the hood of your Nissan Qashqai.
Step 2: Loosen and remove the oil filler cap for better airflow.
Step 3: Pour the recommended engine flush into the engine.
Step 4: Securely replace the oil filler cap.
Step 5: Start your Qashqai’s engine and let it idle for 15 minutes before shutting it off.
Step 6: Safely elevate the vehicle either with a jack or by positioning it over an inspection pit. Ensure the vehicle remains level.
Step 7: Loosen the fasteners holding the oil pan’s lower cover.
Step 8: Gently remove the oil pan cover. Utilize a #10 socket and a flat screwdriver if needed.
Step 9: Place a container with a minimum 5-liter capacity beneath the oil drain plug.
Step 10: Use a no.19 socket or ring spanner to unscrew the drain plug.
Step 11: Allow all the old oil to drain out into the container.
Step 12: Position the container directly beneath the oil filter.
Step 13: Use a 65/67-14f socket to unscrew and remove the oil filter.
Step 14: Dispose of the old oil filter by placing it in a dedicated container.
Step 15: Ensure the oil filter seating area is thoroughly cleaned.
Step 16: Also, clean around the oil pan’s drainage hole.
Step 17: Insert a new drain plug and secure it with a torque of 34 nm using a torque wrench.
Step 18: Apply a slight coat of new engine oil to the rubber seal of the new oil filter.
Step 19: Hand-tighten the new oil filter in its position and then further tighten it to 18 nm torque using a torque wrench and the 65/67-14f socket.
Step 20: Reposition the oil pan’s lower cover.
Step 21: Tighten all fasteners on the oil pan’s lower cover.
Step 22: Remove the oil filler cap once again.
Step 23: Place a funnel into the opening.
Step 24: Pour in 4.3 liters of the manufacturer-recommended oil into the engine.
Step 25: Securely tighten the oil filler cap. Afterward, check the oil level with a dipstick, adjusting if necessary.
Step 26: Run the engine briefly. Once the oil pressure light deactivates, turn off the engine.
Step 27: After 5 minutes, recheck the oil level with the dipstick, adding oil if needed.
Step 28: Finally, shut the hood, ensuring it’s securely latched.
Note: Always follow safety precautions when working on vehicles, and ensure the use of protective gear.